有机封装基板界面处理工艺对结合强度与可靠性的影响

doi:10.16257/j.cnki.1681-1070.2024.0037

电子与封装 ›› 2024, Vol. 24 ›› Issue (2): 020105 . doi: 10.16257/j.cnki.1681-1070.2024.0037

• “高密度有机封装基板”专题 • 上一篇下一篇

有机封装基板界面处理工艺对结合强度与可靠性的影响

梁梦楠,陈志强,张国杰,姚昕,李轶楠,张爱兵

无锡中微高科电子有限公司，江苏无锡? 214035

收稿日期:2023-10-08 出版日期:2024-02-29 发布日期:2024-02-29
作者简介:梁梦楠（1992—），男，河南商丘人，硕士，工程师，主要研究方向为封装基板研发。

Effect of Interface Processing Technology on Bonding Strength and Reliability of Organic Package Substrate

LIANG Mengnan, CHEN Zhiqiang, ZHANG Guojie, YAO Xin, LI Yi´nan, ZHANG Aibing

Wuxi Zhongwei High-Tech Electronics Co., Ltd., Wuxi 214035, China

Received:2023-10-08 Online:2024-02-29 Published:2024-02-29

摘要/Abstract

摘要： 封装基板分层是塑封电路常见的一种失效模式，塑封基板分层会导致整个电路出现开路问题。基板分层通常与其界面间结合强度不足、基板水汽等有关。研究了铜表面的粗化处理、味之素堆积膜（ABF）表面的等离子清洁对铜和ABF表面的形貌、粗糙度以及界面间结合的影响，粗化后的铜表面与ABF树脂的剥离界面分析结果证明界面间断裂失效属于物理结合力失效。同时还对基板加工过程的吸水率及不同烘烤参数对除水效果的影响进行了研究。通过引入铜面粗化处理、等离子清洁和增层前烘烤，解决了基板封装后出现分层的问题，同时封装后的产品通过了部分热可靠性测试。

关键词: 封装基板, 味之素堆积膜, 粗化处理, 等离子清洁, 封装可靠性

Abstract: Package substrate delamination is a common failure mode in the plastic packaged circuit, and plastic package substrate delamination will lead to open circuit problem throughout the circuit. Substrate delamination is usually related to weak bonding strength between interfaces and moisture in the substrate. Effects of roughening of the copper surface and plasma cleaning of the Ajinomoto buildup film (ABF) surface on the morphology, roughness and interfacial bonding of the copper and the ABF surface are studied. Analysis results of the stripping interfaces between the roughened copper surfaces and ABF resins show that the fracture failure between interfaces is a physical bonding failure. At the same time, the water absorption during substrate processing and the influence of different baking parameters on the water removal effect are also investigated. Through the introduction of copper surface roughening treatment, plasma cleaning and baking before lamination, the problem of delamination after substrate package is solved, while the packaged products pass some thermal reliability tests.

Key words: package substrate, Ajinomoto buildup film, roughening treatment, plasma cleaning, package reliability

中图分类号:

TN305.94

梁梦楠,陈志强,张国杰,姚昕,李轶楠,张爱兵. 有机封装基板界面处理工艺对结合强度与可靠性的影响[J]. 电子与封装, 2024, 24(2): 020105 .

LIANG Mengnan, CHEN Zhiqiang, ZHANG Guojie, YAO Xin, LI Yi´nan, ZHANG Aibing. Effect of Interface Processing Technology on Bonding Strength and Reliability of Organic Package Substrate[J]. Electronics & Packaging, 2024, 24(2): 020105 .

参考文献

[1] 桂萌琦，方志丹. 先进封装基板[J]. 微纳电子与智能制造, 2021, 3(1): 98-103.
[2] 向静. 封装基板互连结构电沉积铜机理与应用研究[D]. 成都: 电子科技大学, 2018.
[3] 贾莉萍. 无核封装基板铜面修饰及界面结合效果的研究[D]. 成都: 电子科技大学, 2018.
[4] 何刚，李太龙，万业付，等. IC封装基板及其原材料市场分析和未来展望[J]. 中国集成电路, 2021, 30(11): 31-36.
[5] 杨建伟. 封装基板阻焊层分层分析与研究[J]. 电子与封装, 2019, 19(2): 1-4, 12.
[6] 侯朝昭，邵远城，李茂源，等. IC封装无芯基板的发展与制造研究[J]. 电子工艺技术, 2014, 35(4): 187-189, 233.
[7] 周文木，徐杰栋，吴梅珠，等. IC封装基板超高精细线路制造工艺进展[J]. 电子元件与材料, 2014, 33(2): 6-9, 15.
[8] 蔡积庆. 积层绝缘树脂沾污去除和化学镀铜工艺[J]. 印制电路信息, 2012, 20(2): 26-30.
[9] OH Y, KIM E J, KIM Y, et al. Adhesion of sputter-deposited Cu/Ti film on plasma-treated polymer substrate[J]. Thin Solid Films, 2016, 600: 90-97.
[10] ZABETAKIS D, DRESSICK W J. Selective electroless metallization of patterned polymeric films for lithography applications[J]. ACS Applied Materials and Interfaces, 2009, 1(1): 4-25.
[11] GRANADO L, KEMPA S, GREGORIADES L J, et al. Improvements of the epoxy-copper adhesion for microelectronic applications[J]. ACS Applied Electronic Materials, 2019, 1(8): 1498-1505.
[12] SASAKI S, TANI M. Via formation process for smooth copper wiring on insulation layer with adhesion layer[J]. Transactions of the Japan Institute of Electronics Packaging, 2013, 6(1): 7-12.
[13] 李浩霖. 印制电路内层铜面低粗糙度锡/硅烷处理技术及其应用研究[D]. 成都: 电子科技大学, 2021.
[14] TANI M, SASAKI S, UENISHI K. Adhesion improvement on smooth Cu wiring surfaces of printed circuit boards[J]. Transactions of the Japan Institute of Electronics Packaging, 2011, 4(1): 24-30.
[15] Institute for Printed Circuit Boards. IPC-TM-650 CN试验方法手册：IPC-TM-650[S]. 美国：美国印制电路板协会，2020.
[16] NAKAGAWA T. The relationship between self-annealing of plated copper and copper surface treatment[J]. Circuit World, 2003, 29(3): 22-26.
[17] NAKASO A. Innerlayer copper surface treatment for multilayer printed wiring boards[J]. Journal of the Surface Finishing Society of Japan, 1994, 45(2): 192-196.
[18] 黄卫东. 高可靠性电子封装中防潮薄膜技术的研究[D]. 上海：中国科学院上海微系统与信息技术研究所, 2003.
[19] HAYDEN H, ELCE E, ALLEN S A B, et al. Adhesion enhancement between electroless copper and epoxy-based dielectrics[J]. IEEE Transactions on Advanced Packaging, 2009, 32(4): 758-767.
[20] 罗莉. 印制电路板铜/树脂耐剥离性新型棕化工艺的研究[D]. 重庆: 重庆大学, 2018.
[21] 韦进峰，唐海波，李恢海. 印制电路板加工中孔内与板面除胶差异研究[J]. 印制电路信息, 2021, 29(5): 23-28.
[22] KEMPA S, FRIZ W, GAUL F, et al. Investigation of a proactive glass filler removal in IC substrate build up films and its effect on topography and copper adhesion reliability[C]// International Microelectronics Assembly and Packaging Society, 2018.
[23] 方志丹，于中尧，武晓萌，等. FCBGA基板关键技术综述及展望[J]. 电子与封装, 2023, 23(3): 030103.

中国半导体行业协会封装分会会刊

中国电子学会电子制造与封装技术分会会刊

有机封装基板界面处理工艺对结合强度与可靠性的影响

Effect of Interface Processing Technology on Bonding Strength and Reliability of Organic Package Substrate

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 3

编辑推荐

Metrics

本文评价

[1]	杨昆,朱家昌,吉勇,李轶楠,李杨. 有机封装基板的芯片埋置技术研究进展[J]. 电子与封装, 2024, 24(2): 20102-.
[2]	李锟,曹易,田欣,薛超. 有机封装基板标准化工作现状及发展思考[J]. 电子与封装, 2024, 24(2): 20107-.
[3]	李轶楠, 杨昆, 陈祖斌, 姚昕, 梁梦楠, 张爱兵. 无芯封装基板应力分析与结构优化^*[J]. 电子与封装, 2023, 23(8): 80203-.