纳米银焊膏贴装片式电阻的可靠性研究*

doi:10.16257/j.cnki.1681-1070.2023.0104

电子与封装 ›› 2023, Vol. 23 ›› Issue (8): 080204 . doi: 10.16257/j.cnki.1681-1070.2023.0104

纳米银焊膏贴装片式电阻的可靠性研究^*

王刘珏;顾林;郑利华;李居强

中国电子科技集团公司第五十八研究所，江苏无锡 214035

收稿日期:2022-09-08 出版日期:2023-08-24 发布日期:2023-08-24
作者简介:王刘珏（1992—），男，安徽安庆人，博士，工程师，主要研究方向为电子封装技术及可靠性分析。

ReliabilityStudy of Chip ResistorMounted With Nano-Silver Solder Paste

WANG Liujue, GU Lin, ZHENG Lihua, LI Juqiang

China ElectronicsTechnology Group Corporation No.58Research Institute, Wuxi 214035, China

Received:2022-09-08 Online:2023-08-24 Published:2023-08-24

摘要/Abstract

摘要： 采用纳米银焊膏对片式电阻进行表面贴装，并且通过加速老化试验模拟片式电阻焊点的服役环境，研究了不同的环境可靠性条件下焊点界面显微组织演变以及力学性能的变化。结果表明，纳米银焊膏采用无压烧结工艺能够实现片式电阻的表面贴装。经过环境可靠性验证后，虽然片式电阻焊点横截面的显微组织出现粗化现象，剪切断口的塑性变形区域逐渐缩小，但是其力学性能仍然满足GJB 548B-2005《微电子器件试验方法和程序》的规定。

关键词: 纳米银焊膏, 片式电阻, 环境可靠性, 显微组织, 力学性能

Abstract: Nano-silver solder paste is used to mount the chip resistors, and the service environment of chip resistance solder joints is simulated by accelerated aging test. The microstructure evolution and mechanical properties of the chip resistor joints under different environmental reliability conditions are studied.The results show that the nano-silver solder paste can achieve surface mounting of chip resistors using a pressureless sintering process. After environmental reliability verification, although the cross-sectional microstructure of the chip resistor jointsappear coarsening and the area of plastic deformation in the shear fracture is gradually reduced, but the mechanical properties of the chip resistor joints still meet the requirements of GJB 548B-2005 TestMethods and Procedures for Microelectronic Devices.

Key words: nano-silver solder paste, chip resistor, environmental reliability, microstructure, mechanical properties

中图分类号:

TG425

王刘珏, 顾林, 郑利华, 李居强. 纳米银焊膏贴装片式电阻的可靠性研究^*[J]. 电子与封装, 2023, 23(8): 080204 .

WANG Liujue, GU Lin, ZHENG Lihua, LI Juqiang. ReliabilityStudy of Chip ResistorMounted With Nano-Silver Solder Paste[J]. Electronics & Packaging, 2023, 23(8): 080204 .

参考文献

[1] 蔡志清. 雷达用片式电阻器件激光钎焊技术研究[J]. 现代雷达，2020，42(12)：88-91.
[2] COLLINS M N, PUNCH J, COYLE R. Surface finish effect on reliability of SAC 305 soldered chip resistors[J], Soldering & Surface Mount Technology, 2012, 24(4): 240-248.
[3] REID M, COLLINS M N, DALTON E, et al. Testing method for measuring corrosion resistance of surface mount chip resistors[J]. Microelectronics Reliability, 2012, 52(7): 1420-1427.
[4] 薛松柏，王俭辛，禹胜林，等. 热循环对片式电阻Sn-Cu-Ni-Ce焊点力学性能的影响[J]. 焊接学报，2008，29(4)：5-8.
[5] 徐龙会，蒋廷彪，杜超. 片式电阻混合焊点热循环负载可靠性研究[J]. 电子元件与材料，2007，26(8)： 67-70.
[6] 马超力，薛松柏，李阳，等. 时效对Sn-Cu-Ni-xPr/Cu焊点组织与性能的影响[J]. 焊接学报，2014，35(3)：85-88.
[7] SEO W, KO Y H, KIM Y H, et al. Void fraction of a Sn-Ag-Cu solder joint underneath a chip resistor and its effect on joint strength and thermomechanical reliability[J]. Journal of Material Science: Materials in Electronics, 2019, 30(17): 15889-15896.
[8] 肖玲，何万波. 导电胶粘接元件接触电阻的稳定性研究[J]. 微电子学，2016，46(4)：576-580.
[9] 薛伟锋，刘炳龙. 微波芯片元件的导电胶粘接工艺与应用[J]. 电子工艺技术，2012，33(3)：156-159.
[10] CHEN C T, YEOM J, CHOE C Y, et al. Necking growth and mechanical properties of sintered Ag particles with different shapes under air and N2 atmosphere[J]. Journal of Materials Science, 2019, 54(20): 13344-13357.
[11] ZHANG H, CHEN CT, JIU J T, et al. High-temperature reliability of low-temperature and pressureless micron Ag sintered joints for die attachment in high-power device[J]. Journal of Materials Science: Materials in Electronics, 2018, 29(10): 8854-8862.
[12] 李聪成，滕鹤松，王玉林，等. 无压惰性气氛银烧结层空洞率影响因素研究[J]. 电子与封装，2017, 17(11)：6-9.
[13] 胡博. SiC颗粒复合纳米银膏的制备及低温烧结互连机理研究[D]. 深圳：哈尔滨工业大学（深圳），2019.
[14] WANG S, LI M Y, JI H J, et al. Rapid pressureless low-temperature sintering of Ag nanoparticles for high-power density electronic packaging[J]. Scripta Materialia, 2013, 69(11-12): 789-792.
[15]ZHANG Z, CHEN C T, YANG Y, et al. Low-temperature and pressureless sinter joining of Cu with micron/submicron Ag particle paste in air[J]. Journal of Alloys and Compounds: An Interdisciplinary Journal of Materials Science and Solid-state Chemistry and Physics, 2019, 780: 435-442.
[16] 李自平. 分散剂对纳米银浆烧结质量影响的研究[D]. 哈尔滨：哈尔滨工业大学，2012.
[17] ZHANG J, HUANG F, LIN Z, et al. Progress of nanocrystalline growth kinetics based on oriented attachment[J]. Nanoscale, 2010, 2(1): 18-34.

中国半导体行业协会封装分会会刊

中国电子学会电子制造与封装技术分会会刊

纳米银焊膏贴装片式电阻的可靠性研究^*

ReliabilityStudy of Chip ResistorMounted With Nano-Silver Solder Paste

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 5

编辑推荐

Metrics

本文评价

[1]	李志豪,汪松英,洪少健,孙啸寒,曾世堂,杜昆. 镀银板表面粗糙度对纳米银焊膏快速烧结互连质量的影响[J]. 电子与封装, 2024, 24(7): 70201-.
[2]	张宸赫,李盼桢,董浩楠,陈柏杉,黄哲,唐思危,马运柱,刘文胜. 高功率半导体用纳米银焊膏的研究现状^*[J]. 电子与封装, 2024, 24(5): 50203-.
[3]	侯冰玉,盛依航,耿秀侠,胡俊,王剑,王世堉,王明智. 鱼眼型高速连接器的材料性能识别与压接特性仿真研究[J]. 电子与封装, 2024, 24(3): 30204-.
[4]	王曦;张亮;李木兰;姜楠. 电子组装用Sn-Sb系无铅钎料研究进展^*[J]. 电子与封装, 2023, 23(2): 20201-.
[5]	李海军;宗福春;胡增武;李云飞;彭文佳;齐敬. 硅含量对硅铝合金电子封装材料性能的影响[J]. 电子与封装, 2022, 22(12): 120203-.